Seite - 1618 - in Book of Full Papers - Symposium Hydro Engineering
Bild der Seite - 1618 -
Text der Seite - 1618 -
2.5. REFUSAL AND CLOSURE
Each and every stage of every grout hole must be brought to a true and
proper “refusal” in accordance with Apparent Lugeon Theory. This means that
the maximum specified pressure has been held over a certain period (say 5
minutes) at a certain maximum flow rate (typically 1-3 liters per minute,
depending on the project’s residual permeability goals and the nature of the rock
mass). “Closure,” on the other hand, is when a section of the curtain has been
judged to have been completed with a degree of certainty that the subsequent
verification test holes will indeed confirm that the target residual permeability has
been achieved. A proper judgment of closure depends on a holistic analysis of
all available and relevant information, such as drilling logs, water tests, optical
televiewer logs, grout take analyses and dam instrument response.
Lax refusal criteria will result in incompletely and inefficiently grouted
stages. These can also lead to partially grouted fractures resulting in a high
residual permeability. Given the limited number of fracture intersections by grout
holes and given that the cost of drilling a new hole or holes is likely the most
expensive operation in typical foundation grouting programs, each and every hole
should be viewed as an opportunity to reduce the bedrock permeability and
should be grouted to the fullest extent possible.
Many designers may view the additional time to grout to a low refusal flow
criterion as unnecessary and expensive. To the contrary, the last volumes of
grout injected during the final refusal of a grout stage can be some of the most
important time and effort spent to achieve closure, especially if the time spent
reduces the number of additional holes to complete what the prior holes and
stages were not able to compete. Designers should consider the costs of drilling
additional holes as well as the implications in regards to dam safety (especially
for holes that need to be drilled and installed through embankments) when
setting refusal flow criteria. Additional time grouting to low refusal criteria will help
to reduce the number of additional holes to be added, drilled, water pressure
tested, and grouted. All of these operations come with some measured amount of
risk involving dam safety, so a reduction in the number of instances that these
operations are performed should be viewed as an improvement.
One of the gifts we accept from the use of stable grouts (i.e., those grouts
with minimal bleed and pressure filtration) is that they maintain a relatively
constant rheology during their period of injection: they do not allow water to be
squeezed out of the mix, into fissures, when under pressure. Thus, a grout with
constant rheology (i.e., like water has) can thus be regarded as not only a fissure
filler, but also a test fluid. This allows us to calculate an Apparent Lugeon Value
during the initital grouting of any stage, calculated in the same way as a Water
(True) Lugeon Value, but corrected by a factor being Marsh time (grout) / Marsh
time (water).
Grout curtains should always be grouted to a target True Lugeon Value
(residual permeability). Individual stages should be brought towards refusal by
observing and controlling the Apparent Lugeon value, subject to the final “refusal”
flow rate. Grout curtains should not be brought to closure based solely on
1618
Book of Full Papers
Symposium Hydro Engineering
- Titel
- Book of Full Papers
- Untertitel
- Symposium Hydro Engineering
- Autor
- Gerald Zenz
- Verlag
- Verlag der Technischen Universität Graz
- Ort
- Graz
- Datum
- 2018
- Sprache
- englisch
- Lizenz
- CC BY-NC-ND 4.0
- ISBN
- 978-3-85125-620-8
- Abmessungen
- 20.9 x 29.6 cm
- Seiten
- 2724
- Schlagwörter
- Hydro, Engineering, Climate Changes
- Kategorien
- International
- Naturwissenschaften Physik
- Technik