Seite - 1752 - in Book of Full Papers - Symposium Hydro Engineering
Bild der Seite - 1752 -
Text der Seite - 1752 -
Table 1. Summary of Estimated Seepage Rate for the Reservoir Based on Permeability Test Results
Permeability
Range (cm/s)
Average
Permeability
(cm/s)
Reservoir
Area
(Percentage)
Seepage Rate
(m3/s)
Annual
Seepage
(million m3) 10-6 – 10-5
4.06×10-6
24.4
0.023
0.72
10-5 – 10-4
4.10×10-5
5.4
0.051
1.61
10-4 – 10-3
3.15×10-4
32.4
2.36
74.35
10-3 – 10-2
3.29×10-3
37.8
28.73
905.95
Total
1.35×10-3
100
31.16
983
Calculated seepage rate based on the above assumption and parameters was 31.16m3/s. With the
assumption of full reservoir, this leads to an annual seepage rate of approximately 1 billion cubic
meters. This suggested that water tightening and through insulation for the reservoir was essential
for the Chitgar Lake Project.
Due to the significant depth of alluvium (more than 100m), water tightening underneath the dam
body and the perimeter dyke was impractical and the only feasible option was continuous
interconnection of the water tightening membrane over the entire area of the reservoir and extending
to upstream face of the dam. This solution provides many advantages compared to other possible
remedies such as elimination of dam foundation water tightening activity, seepage-free dam body
resulting in size reduction of the dam’s core and finally ease of construction.
3. Lake Water tightening Alternatives
3.1. Water tightening using Clay Blanket
One method for the purpose of reservoir water tightening is to use Clay Blanket. As common
practice, in order to have a functional clay blanket with a permeability rate of 1×10-7 and less,
materials with following specifications should be used: 50% passing rate through No. 200 Filter, a
minimum 20% clay material, above 20% Plasticity Index (PI) and above 30% Liquidity Index (LL)
Index.
Overall, due to the poor condition of
reservoir fine-grain material and
unavailability of suitable material in
proximity of the project which lead to
undesirable seepage, the option of Clay
Blanket was rejected. Another
disadvantage of the use of Clay Blanket
was the possibility of plant growth on the
surface which can contribute to pollution
of the Lake and have negative
environmental impact. Figure 3. Section Details for Clay Blanket Option
3.2. Water tightening using Impervious Concrete Layer
Use of impervious concrete layer for large reservoirs such as Chitgar Lake's is not common due to
the significant size and importance and functional requirements of the Lake. From the geotechnical
perspective, impervious concrete layer should be placed on the alluvium with a concrete thickness
of about 30cm plus uniform thermal reinforcement and water-tight joints every 12 to 15 meters.
Due to the high cost and relatively lengthy implementation time, the impervious concrete layer was
not considered as a suitable option when compared to other feasible options.
1752
Book of Full Papers
Symposium Hydro Engineering
- Titel
- Book of Full Papers
- Untertitel
- Symposium Hydro Engineering
- Autor
- Gerald Zenz
- Verlag
- Verlag der Technischen Universität Graz
- Ort
- Graz
- Datum
- 2018
- Sprache
- englisch
- Lizenz
- CC BY-NC-ND 4.0
- ISBN
- 978-3-85125-620-8
- Abmessungen
- 20.9 x 29.6 cm
- Seiten
- 2724
- Schlagwörter
- Hydro, Engineering, Climate Changes
- Kategorien
- International
- Naturwissenschaften Physik
- Technik