Seite - 1876 - in Book of Full Papers - Symposium Hydro Engineering
Bild der Seite - 1876 -
Text der Seite - 1876 -
Table 2
Applied parameters for the stress-strain model [2]
BCE preferred to apply an elastic-plastic material model rather than the
linear-elastic models which were used before. Fundamental considerations
concerning the deformation behaviour of rockfill and sand-gravel fill materials were
considered as discussed in [4] [6] [7] [8]. Case studies with reference to principle
rockfill characteristics are also included in [9] and [10]. Sand-gravel fill materials
with a wide, uniform sieve curve tend to show very strong deformation
characteristics which is confirmed by several benchmark projects [7].
For the elastic-plastic modeling constant elasticity moduli were considered
as well as MC shear strength parameter. This approach is considered especially
for the impoundment phase a priori too simplified but, nevertheless, lead to
reasonable results, thanks to an accurate calibration of the model by comparison
to the actual measurement data to reliable results (see chapter 4).
For the performed slope stability LEA following parameters (Table 3) were
applied in order to consider a comprehensive shear-strength behaviour of the
different applied materials. For the main fills (zones 3E, 3F, 3G) stress dependent
shear curves were implemented which were derived from large scale triaxial tests
performed in Germany, as aforementioned.
Models
Source
Zone E
[MPa] n [-] g
[kN/m³] E
[MPa] n [-] g
[kN/m³] E
[MPa] n [-] g
[kN/m³] E
[MPa] n [-] g
[kN/m³] j'
[°] y
[°]
1A 20 0,35 18 20 0,35 19 20 0,3 17 20 0,35 19 30 0
1B 30 0,3 18 80 0,33 21 200 0,3 21,5 80 0,33 21 35 4
2A 360 0,3 22,5 300 0,3 21 - - - 300 0,3 21 38 10
2B 160 0,3 22 250 0,3 21 200 0,3 22 250 0,3 21 40 10
3E 240 0,33 23 220 0,33 24 175 0,38 22 220 0,33 24 38 12
3F 200 0,33 22,5 220 0,33 24 200 220 0,33 24 38 12
3G 120 0,33 20,5 80 0,28 22 200 80 0,28 22 45 15
3H 120 0,33 19 100 0,3 19 150 100 0,3 19 38 4
3H* - - - 100 0,3 19 - - - 100 0,3 19 38 4
ALL 200 0,33 22 150 0,33 19 660 - - 150 0,33 19 35 8
ROCK 5000 0,15 26 20000 0,25 27 15000 0,2 26 20000 0,25 26 - -
CON 20000 0,25 25 20000 0,2 25 28000 0,2 24 20000 0,20 25 - -
F-ALL - - - 200 0,33 24 - - - 200 0,33 24 38 10
RR - - - 60 0,35 24 - - - 60 0,35 24 - -
COW - - - 800 0,27 23 - - - 800/1200/1800 0,26 24 - -
Björnsen Consulting
Engineers
Elastic-plastic
(MC)Linear-elastic
Björnsen Consulting
Engineers
Linear-elastic
Local design
engineer
Linear-elastic
International
consultant
1876
Book of Full Papers
Symposium Hydro Engineering
- Titel
- Book of Full Papers
- Untertitel
- Symposium Hydro Engineering
- Autor
- Gerald Zenz
- Verlag
- Verlag der Technischen Universität Graz
- Ort
- Graz
- Datum
- 2018
- Sprache
- englisch
- Lizenz
- CC BY-NC-ND 4.0
- ISBN
- 978-3-85125-620-8
- Abmessungen
- 20.9 x 29.6 cm
- Seiten
- 2724
- Schlagwörter
- Hydro, Engineering, Climate Changes
- Kategorien
- International
- Naturwissenschaften Physik
- Technik