Page - 1874 - in Book of Full Papers - Symposium Hydro Engineering
Image of the Page - 1874 -
Text of the Page - 1874 -
design and in order to check the stability also for extreme seepage conditions
superposed with earthquake loads. For the LEA of the slopes the program
Slide/Rocscience was applied.
3.2. FEM MODELS, INPUT PARAMETER AND ANALYSES
The seepage FE model is shown in Fig. 3. The finite element mesh was
refined at critical structural objects such as the face slab and the articulated plinth
as well as close to the cut-off wall and the L-shaped drain. Steady state conditions
were investigated for different water levels and for different sealing and drain
conditions which were combined to load cases (LC).
Fig. 3
FE mesh and model for the seepage analysis
For the steady state seepage analysis following parameters, e. g.
permeability, were applied (Table 1). Table 1 includes the general Technical
Specifications of the dam fill works.
Table 1
Technical specifications of the main dam fill materials Fehler! Verweisquelle
konnte nicht gefunden werden.
The FE mesh used for the stress-strain analysis (Sigma/W) is given in Fig. 4.
The mesh had to be critically refined in the area of stiff objects such as the concrete
No. Name Description Passes
[-] Dry
density4)
sd [g/cm³] Max. grain
size
dmax [mm] Layer
thickness
T [cm] Elasticity
modulus
E [MPa] Permeability
k [m/s] Water
[l/m³] Model "Set0"
k-values
[m/s]
1 1A3) Cohesionless fine grained soil - - 63 30 - - - 10-5
2 1B3) Fill, protection material - - 400 60 - - - 10-4
3 2A Perimeter filter 8 2.0 40 40 - - - Not modeled.
4 2B Transition filter I 8 2.0 80 40 - - - 10-5
5 3E Upstream sand-gravel fill 12 2.5 400 60 200 10-4 5) 10-4
6 3F Downstream sand-gravel fill 12 2.5 600 80 200 10-4 5) 10-4
7 3G Downstream rockfill 12 2.2 600 80 802) 10-1 to 10-2 250-500 10-1
8 3H L-shaped drain/filter 8 1.9 150 60 - 10-2 - 5 10-2
9 3H* Suffusion filter 8 2.0 150 60 - 10-3 - 10-3
10 RR Rip-rap - - 1,500 150 - 10-1 - Not modeled.
Notes:
1)
2)
3)
4)
5)
6) This value reflects the target value which was not included in the TechSpecs and the civil contract.
For all materials a smooth drum vibrator compacter (SDVC) with a static weight of 15-16 tons will be used. The speed is limited to 2.5-3.5 km/h.
General Technical Specifications for the Fill works1)6)
"Set0" reflects the standard set of applied conductivity values for the seepage analysis. For "Set1" the seepage relevant zones were increased by the factor
10, for "Set2" decreased by this factor. For "Set3", only the sand-gravel materials (3F, 3E, ALL) were assumed to show a permeability of k = 10 -3
m/s.
For fill materials upstream of the face slab (1A,1B) no or only slight compaction work is required.
The given values reflect check values which are controlled during construction.
The sand-gravel fill needs no watering since the residual moisture content is close to the "optimum moisture content". If too
dry the material should be watered before compaction by pressureless water. The material must not be completely
saturated.
1874
Book of Full Papers
Symposium Hydro Engineering
- Title
- Book of Full Papers
- Subtitle
- Symposium Hydro Engineering
- Author
- Gerald Zenz
- Publisher
- Verlag der Technischen Universität Graz
- Location
- Graz
- Date
- 2018
- Language
- English
- License
- CC BY-NC-ND 4.0
- ISBN
- 978-3-85125-620-8
- Size
- 20.9 x 29.6 cm
- Pages
- 2724
- Keywords
- Hydro, Engineering, Climate Changes
- Categories
- International
- Naturwissenschaften Physik
- Technik