Page - 2197 - in Book of Full Papers - Symposium Hydro Engineering
Image of the Page - 2197 -
Text of the Page - 2197 -
explained that the physical volume of electricity generation in the first quarter of 2017 was
698,451MWh, causing an increase of 57.4% compared to the first quarter of 2016 generation of
443,628MWh [9]. But barriers to clean energy worldwide are augmented all over the concerned
countries of sub-Saharan Africa, also financial resources are minimal as well as unreliability of
infrastructure. In sub-Saharan Africa, there is a lack of electricity infrastructure for large-scale
renewable energy industries. For example, in Kenya, there are at least 50 power outages per year.
Increasingly, countries in sub-Saharan Africa are implementing energy through renewable energy
resources and efficacy. Kenya, as one of the most dynamic countries, increased its geothermal
energy capacity to 740MW in 2015, and plans to launch a $ 150 billion project to invest solar energy
in areas where Electricity is not accessible and are not connected to the grid. Ethiopia on the other
hand is also principally active in wind power (150MW), and also stepping up its efforts in solar
energy with the construction of a 5.200MW plant which is the largest in the region. In addition,
several projects in Addis Ababa are underway, including geothermal and solar projects, and are
intended to be open to the private sector. The figures below show renewable status in the region
between 2010 to 2016[10]
2.2. CONCEPT OF PUMP RUNNING IN REVERSE MODE AS TURBINE
The velocity diagram for the flow at the inlet and discharge of a pump runner are basically matching
when the unit operates as a turbine, except for the reversing of each vector as can be seen Fig. 9.5
and Fig. 9.6. Fig. 10 provides better understanding to the concept of pump operating in pump mode
and in reverse mode as turbine
Fig. 7.5: Velocity Diagrams at the Inlet and Fig.7.6: Velocity Diagrams at the Inlet and
Outlet of Centrifugal Pump [11] Outlet of Impeller Under Reverse Flow [11]
PAT CHARACTERISTICS
It is well known that efficiency of a centrifugal pump decreases rapidly with a drop of specific speed,
and the impeller outlet diameter should be reduced considerably to increase its efficiency. With a
reduced outlet diameter, it is necessary to select a larger blade discharge angle and more blades to
produce the rated head. However, too many blades result in a decrease in efficiency due to the
increasing blockage and skin friction in the impeller passage. Yuan [13] revealed that the splitter
blade technique is one of the techniques to solve three hydraulic problems of low specific speed
centrifugal pumps (lower efficiency, drooping head-flow curve and easily overloaded brake
horsepower characteristics). It was observed from the studies that low or high blade numbers had
increased the instability risk of head-flow curves [14], and the optimum efficiency was obtained
when the blade number was between 4 and 6 [15]. M Asuaje et al. [16] studied the splitter blades
effect on the performance of a centrifugal pump through both numerical simulation and experimental
results. Adding splitters has negative and positive effects on the pump behavior. It increases the head
rise compared to the original impeller, it has positive effect on decreasing the vibrating and radiated
noise; but the efficiency is not improved since the hydraulic losses are greater. J. Zhang et al.
conducted a study using the A BP artificial neural network (BPANN) model of a three-layer with 5
2197
Book of Full Papers
Symposium Hydro Engineering
- Title
- Book of Full Papers
- Subtitle
- Symposium Hydro Engineering
- Author
- Gerald Zenz
- Publisher
- Verlag der Technischen Universität Graz
- Location
- Graz
- Date
- 2018
- Language
- English
- License
- CC BY-NC-ND 4.0
- ISBN
- 978-3-85125-620-8
- Size
- 20.9 x 29.6 cm
- Pages
- 2724
- Keywords
- Hydro, Engineering, Climate Changes
- Categories
- International
- Naturwissenschaften Physik
- Technik